Welcome to our company!

Nanjing EFG Co.,Ltd
Fiberglass Composite Mat (Continuous Filament and Polyester Surface Mat)

Fiberglass Composite Mat (Continuous Filament and Polyester Surface Mat)

Polyester Fiberglass Composite Mat (Polyester Fiberglass Paving Mat) is produced from the mixture of polyester fiber and glass fiber by wet lay-out process. The combination of glass fiber and polyester fiber is the key to its performance. After mixing the two...

Product Details

With our high-quality, efficient management and innovative business philosophy, our company is unique in the Reinforced Cotton Mat, Fiberglass Panel, Reinforced Polyester Paving Mat field and has a high reputation. Our company has put in place a comprehensive system of training of the personnel to ensure the stability and the development of the quality of the personnel. We create value not only rely on products, but more importantly, making sure that each product complies with national environmental protection regulations and emission standards.

Polyester Fiberglass Composite Mat (Polyester Fiberglass Paving Mat) is produced from the mixture of polyester fiber and glass fiber by wet lay-out process. The combination of glass fiber and polyester fiber is the key to its performance. After mixing the two fibers together, the polyester fiberglass mat keeps good features of both fibers and minimizes shortcomings of both fibers.

Strong tensile strength make polyester-fiberglass composite mat especially suitable for waterproofing of payments; it extends the life of pavement through the delay of reflective cracking. Polyester fiberglass composite mat also serves as an effective moisture barrier. The unique, non-woven, polyester-fiberglass structure of the mat allows asphalt binder to fully penetrate and fill voids within the mat, limiting moisture infiltration and preventing water from infiltrating into the granular layers of the pavement structure.

Polyester- Fiberglass Composite Mat creates innovative solutions to help the paving projects to go smoothly and provides superior performance on airport runway, super highway, parking area and business lots. 


Technical data 


Nature

Units

Typical


Product Code


PF1003/5

PF136-600

Area Weight

G/m2

90-110

130-150

Tensile Strength MD

N/5cm

220

300

Tensile Strength CD

N/5cm

220

300

Polyester fiber content

%

20-40

20-40

Glassfiber content

%

50-70

50-70

Binder content

%

15-25

15-25

Thickness

mm

0.8

≤1.2

Melting point

230

230

Asphalt absorption capacity

L/m2


1.11

elongation MD

%

<5

<5

elongation CMD

%

<5

<5


Customization: 

Above technical dates are standard for our company. Of course we can produce as per your requirement . First , tell us your requirement or where you will use the products, then we will make samples and send you by courier. Please comment on /confirm the samples we send. We will try out best to satisfy you need. And of course our fibre glass price is reasonable. 


Application:  

1. PF1003/5 is used as waterproofing, insulation and soundproof material on the wall and ceiling.

2. PF136-600 is used as paving mat on highway, airport runway and some other business lots. 

1   2


As an excellent paving material, the material PF136-600 have the features as bellow:
 Delays reflective cracking
◆ Provides a Moisture Barrier

◆ Easy installation 

◆ Fully Millable and Recyclable

◆ Low risk of product shrinkage during the overlay process 


Instruction to use the polyester fiberglass paving mat:
◆ Remove dirt, gravel and dust from the pavement to assure good adhesion between asphalt and pavement.
◆ If the road is damaged, the road must be repaired to make the surface of the road hard and smooth.
◆ For a good result, the asphalt that will be used to adhere the polyester fiberglass mat with the road must be hot asphalt, but not emulsified asphalt.
◆ The temperature of hot asphalt should be between 163℃ and 204 ℃.
◆ When the hot asphalt covered the road, the polyester fiberglass mat must be overlaid onto the hot asphalt before the asphalt loses it’s mobility so as to ensure the mat fully soaked by asphalt and effectively provides a moisture barrier.  

◆ On installation of the Polyester fiberglass paving mat, the air temperature must be higher than 4 ℃.


In order to achieve optimal results, here we provide some Notes on installation of Composite Paving Mat:
◆ Polyester fiberglass paving mat must be installed on the hot asphalt. We recommend the following asphalt. AC-20; PG64-22; AR8000 +, or asphalt with penetrate rates 60-80. In extremely hot summer, we recommend to use the asphalt with high viscosity, such as AC-30; PG67-22; AR8000 +, or asphalt with penetrate grade 40-60.
◆ The best ratio of asphalt is 1.1 liters / square meters paving mat, but subject to project site situation during the installation, the ratio can be between 1.0-1.3 liters / square meters. According to different area weight of the Composite Paving Mat, the ratio of asphalt should be adjusted accordingly. During the asphalt delivery, we do not advise to heat the asphalt above to a temperature higher than 204 ℃, because this would hinder the pre-mature of liquid asphalt.
◆ Handle the polyester fiberglass paving mat with care during the installation, the paving mat might be damaged or it may cause bad result if the paving mat drops from the installation machine.

◆ During the installation, if it forms a stripe bigger than 2.5cm in any direction, the stripes must be cut and overlaid, and the two layers of paving mat must be fully covered by asphalt so as to assure the two layers of paving mat fully soaked in the hot asphalt. Use roller to press the paving mat or use brush to clear out bubbles in the paving mat to ensure the paving mat fully adhered to the road. When covering the hot asphalt to the road, the width of asphalt should be 4 inch more than the width of paving mat. Since the paving mat can not be curved, for the winding area of the road the paving mat can be cut into several pieces and be installed to the road manually or mechanically.  

◆ For the connection of two pieces of paving mat: the two pieces of paving mat must be overlapped together. In the longitudinal direction the overlapped area must be at least 10.2cm; and in the lateral direction, the overlapped area must be at lease 5.1cm.

◆ If the installation machine or other vehicles have to drive on the paving mat, it should not turn directions frequently nor suddenly so as to avoid damaging the paving mat. Do not scatter sand or other object on the paving mat; to avoid asphalt sticking to the tire of the machine, do not minimize the ratio of bitumen.


Packing ,Loading and Delivery:

Mat will be loaded into container in factory, then be delivered to the sea port, finally be shipped to customers port by ships/vessels. Commonly we assure you we can make delivery two weeks on getting your confirmed order. 

3


4


5


Our services:

We are fiberglass factory majored in fiberglass/poly fiber since 2006, having much experiences in this line. You can trust us for our good service, profession, prompt delivery and best price. We can offer any help any time. If you have any question /need, please contact us. 


We use superb production technology, advanced testing equipment, perfect scientific management system, and fast logistics to continue to improve customer satisfaction with our Fiberglass Composite Mat (Continuous Filament and Polyester Surface Mat). Our company has consistently adhered to the corporate policy of 'advancing with the times, pioneering and innovating, and striving for perfection', and has achieved remarkable results. In terms of service, the company will continue to adhere to the customer first business philosophy, continuously improving customer service levels, and increasing customer loyalty.

Send Inquiry

Related Showrooms