We have many years of R&D and manufacturing experience in the field of Fiberglass Joint Tape, Reinforced Fiberglass Paving Mat, Cotton Mat, and can improve the most cost-effective products for you. We always hold on the company's principle 'honest, professional, effective and innovation', and missions of: let all drivers enjoy their driving at night, let our employees can realize their value of life, and to be stronger and service more people. For many years, we have adhered to the principle of customer oriented, quality based, excellence pursuing, mutual benefit sharing. Our products have mainly exported to many countries and sales to all of our country. After years of construction and development, our company has now become a relatively large-scale professional manufacturer of agricultural machinery in China.
Fiberglass Composite Mat
Fiberglass Composite Mat
Fiberglass Composte Mat
Fiberglass Mat +
Fiberglass scrim +
Fiberglass Mat +
Fiberglass scrim +
Area Weight (g/M2)
Mesh Open (ends/cm)
MD & CD yarns (Tex)
Tensile Strength MD
Tensile Strength CD
Above technical dates are standard for our company. Of course we can produce as per your requirement . First , tell us your requirement or where you will use the products, then we will make samples and send you by courier. Please comment on /confirm the samples we send. We will try out best to satisfy you need.
Use as excellent paving mat
◆ Delays reflective cracking
◆ Provides a Moisture Barrier
◆ Easy installation and Less Maintenance
◆ Fully Millable and Recyclable
◆ Low risk of product shrinkage during the overlay process
◆ Tensile strength, roll length, width and area weight can be tailored according to customer’s demand.
Fiberglass Composite Mat (Reinforced fiberglass paving mat) has a combination structure of Fiberglass Mat + Fiberglass Scrim + Fiberglass Mat. The strong fiberglass mesh embedded into the fiberglass mat is the key to its performance, as reinforced fiberglass paving mat extends the life of pavement overlays through the delay of reflective cracking. The Reinforced Fiberglass Paving Mat provides the highest tensile strength with an elongation lower than 5%, making it a strong, commercially available and full coverage paving mat or fabric.
This product also serves as an effective moisture barrier equal to paving fabrics and mats. The unique, non-woven, fiberglass matrix structure of the Reinforced Fiberglass Paving Mat allows asphalt binder to fully penetrate and fill voids within the fabric, limiting moisture infiltration and preventing water from infiltrating into the granular layers of the pavement structure.
Fiberglass Composite Mat creates innovative solutions to help the paving projects go smoothly and provides superior performance on airport runway, super highway, parking area and business lots.
Instruction to use the polyester fiberglass paving mat:
◆ Remove dirt, gravel and dust from the pavement to assure good adhesion between asphalt and pavement.
◆ If the road is damaged, it must be repaired to make the surface of the road hard and smooth.
◆ For a good result, the asphalt binder that will be used to adhere the Paving Mat to the road must be hot asphalt, but not emulsified asphalt.
◆ The temperature of hot asphalt should be between 163℃ and 204 ℃.
◆ When the hot asphalt covered the road, the Reinforced Fiberglass Paving Mat must be overlaid onto the hot asphalt before the asphalt lose it’s mobility so as to assure the mat fully soaked by asphalt and effectively provides a moisture barrier.
◆ For installation of the Reinforced Fiberglass Paving Mat, the air temperature must be higher than 4 ℃.
In order to achieve optimal results, here we provide some Important Notes on installation of Reinforced Fiberglass Paving Mat:
◆Reinforced Fiberglass Paving Mat must be installed on Hot asphalt. We recommend the following asphalt. AC-20; PG64-22; AR8000 +, or the asphalt with penetrate rates 60-80. In extremely hot summer, we recommend to use asphalt with high viscosity, such as AC-30; PG67-22; AR8000 +, or the asphalt with penetrate grade 40-60.
◆ The best ratio of asphalt is 1.1 liters / square meters paving mat, but subject to the project site situation during installation, the ratio can be between 1.0-1.3 liters / square meters. According to different area weight of the Reinforced Fiberglass Paving Mat, the ratio of asphalt should be adjusted accordingly. During delivery of asphalt, we do not advise to heat the asphalt with a temperature higher than 204 ℃, because this would hinder the pre-mature of liquid asphalt.
◆ Handle the Reinforced Fiberglass Paving Mat with care during installation, the paving mat may be damaged or it may cause bad result if the paving mat drop from the installation machine.
During the installation, if it forms a stripe bigger than 2.5cm in any direction, the stripes must be cut and overlaid, and the two layers of paving mat must be fully covered by asphalt so as to assure the two layers of paving mat fully soaked by the hot asphalt. Use roller to press the paving mat or use brush to handle the paving mat so as to clear out bubble in the paving mat to assure the paving mat fully adhered to the road. When covering the hot asphalt to the road, the width of asphalt should be 4 inch more than the width of paving mat. Since the paving mat can not be curved, for the winding area of the road the paving mat can be cut into several pieces and be installed to the road manually or mechanically.
For the connection of two pieces of paving mat, the two layers of paving mat must be overlapped together. In the longitudinal direction the width of overlapped area must be at least 10.2cm, and in the lateral direction, the width of overlapped area must be at least 5.1cm.
◆ If the installation machine or other vehicles have to drive on the paving mat, it should not turn directions frequently nor suddenly, so as to avoid damaging the paving mat. Do not scatter sand or other object on the paving mat; to avoid asphalts sticking to the tire of the machine, do not minimize the ratio of bitumen.
Packing ,Loading and Delivery:
Mat will be loaded into container in factory, then be delivered to the sea port, finally be shipped to customers port by ships/vessels. Commonly we assure you we can make delivery two weeks on getting your confirmed order.
We are fiberglass factory majored in fiberglass/poly fiber since 2006, having much experiences in this line. You can trust us for our good service, profession, prompt delivery and best price. We can offer any help any time. If you have any question /need, please contact us.
In the future, our company will still adhere to the quality policy of 'Quality First, Customer First, Work Together, Pursue Excellence', and strive to be the industry leader with excellent Fiberglass Continuous Filament Mat with Polyester Surface Mat; Fiberglass Composite Mat. We have a high-quality marketing team, perfect and fast after-sales service, the overall customer network describes the world carefully and we have advanced business philosophy and thinking globalization. As the cornerstone of modern civilization, we make our own contribution to improve the level of advanced productivity and promote the continuous accumulation of social wealth.
Fiberglass Mat Composite Mat for Boat Deck
E Grade Fiberglass Chopped Strand Mat 225 Sqm FRP Co...
Aluminium Foil Fiberglass Cloth for Insulation Material
30GSM Fiberglass Surface Tissue for Winding Process
5cm 30GSM Fiberglass Surface Tissue for Making Pipe
Nanometer Glass Lithium Battery Separator